How to: Make DIY Colorful 3D Geometric Wall Art

-
By: Brittni mehlhoff
                                                                           Photo: Brittni Mehlhoff

I created a three-dimensional piece of wall art that is easy to install and relatively inexpensive to make (the final budget came in under $50). Aside from wall art, this project also doubles as a photo booth prop, and if you have the time, it would make an awesome photo booth backdrop too. Want to learn how to make your own? Get the full tutorial and see the finished piece after the jump.

Before you get started, I wanted to touch on color schemes for a second. I thought a lot about the colors I wanted to use beforehand, and had originally selected five colors to use. The fifth color didn't end up working well with the rest, and so I ended up scratching it after a few botched circles. 

So what is the lesson here? Don't be afraid to ditch a color if it's not working. I also recommend sticking to a five color maximum. In this case, the wood acted as my fifth color because I left the bare wood showing in many of the circles.

Okay, now let's get started...

                                                                                   Photo: Brittni Mehlhoff


Supplies Needed:
  1.      Wood circles  *The ones I used are from here and the sizes used are as follows: 4 in, 6.5 in, 8 in, and 10 inch. Similar wood circles can be found at craft stores as well.
  2.     Acrylic craft paint in several colors (up to five), paint brushes, and blue painter's tape
  3.     1/2" thick dowel rods 
  4.     Rotary tool or small saw (to cut the dowels)
  5.     Wood glue
  6.     Sheet of 1/8" - 1/4" hardboard or plywood
  7.     Hammer and nails
  8.     Saw tooth picture hanger 

                                                                                       Photo: Brittni Mehlhoff

How-To:

1. Start by taping off various shapes on one of the wood circles. Be sure to press the tape down securely, especially at the edges, for a crisp line when finished.

2. Paint inside the taped off area, and allow to dry.

3. Remove painter's tape and begin the process again with another color. Or keep it simple, and use only one color. Or use three! Have fun with it.

4. Repeat this process for all of your circles in various sizes, and be sure to mix up the patterns and color combos. 

5. Now, it's time to cut some dowels. Using a rotary tool or saw, cut various lengths from the dowels (I stuck to four different sizes for this project - one short, one medium-short, one medium, and one tall). The dowels will determine how far away each circle will rest from the main wood frame that everything is connected to. NOTE: I also attached several circles straight to the wood panel base, without any dowels, which gave me a fifth height.

6. Once the dowels have been cut, set aside and do a dry fit to roughly map out the positioning for where you want the painted circles to line up when everything comes together. Once you start putting everything together, this layout might change, but it's good to have a game plan when you get started.

7. With the design in place, it's time to start gluing the dowels to the back of each circle. Flip over all of your circles and using wood glue, attach a dowel to the center of each circle and let them dry according to the instructions on the glue bottle. Clamp if necessary for thirty minutes to an hour and do not stress joints for a full 24 hours. You can also use the painter's tape to hold things in place while the glue dries. NOTE: I selected the dowel heights at random, for the most part, making sure that no two circles next to each other would be at the same height.

8. Next attach a saw tooth hanger to the upper center of the hardboard or wood base. Flip over.

9. Now, that you have given the dowels enough time to fully dry and attach securely to the circles, you are ready to attach the dowels to the wood base with more wood glue. Additionally, nails can be hammered through the underside of the wood base and into the dowels for extra security. This helps keep the dowels in place while the glue is drying, in addition to extra security, but is not required.

9. Allow the entire piece to dry for a full 24 hours before hanging.

Aaaaaand! Here is the finished piece: 

Photo: Brittni Mehlhoff

And,  as I said before, it also makes a cool photo booth prop. Or anything prop.
Photo: Brittni Mehlhoff
                                                                                     Photo: Brittni Mehlhoff



Source : www.curbly.com

Comments

Post a Comment

Popular posts from this blog

DIY Brass Chandelier

-
Image
Do you say “Yes, please!” to modern brass lighting fixtures that you can make yourself and customize to your own space? Or maybe you’re of the train of thought where  DIY lighting fixtures  seem overwhelming and intimidating and scary. Either way, you may have seen the  Lindsey Adelman brass chandelier  that has graced cyberspace for a couple of years now, not only because it’s a beauty, but also because it comes in a DIY kit. Which is very convenient, although it’s not the route we took. This step-by-step tutorial you’re reading right now aims to take you through the process of building the brass chandelier in as simple a way as possible, while keeping the entire process completely customized. Let’s dive in. Note:  Author is an experienced, although not professional, electrician. The chandelier-building process is explained as clearly and accurately as possible. Contact a professional with any questions or potential hazards you come across. Home...
Read more

DIY Finger Fishtail Loom Bracelet

-
Image
by Erica The Duchess of Cambridge might have helped ignite the loom band bracelet craze but credit must be given where credit is due. Kids and teens everywhere have been whipping up their version of the friendship bracelet for months now. Made from small, colorful rubber bands, these bracelets are meant to assembled on an inexpensive loom that serves as a base for various patterns. However, you can easily make a simple fishtail version, without the loom, with just two fingers. It is beyond easy. And addicting. I may be past my prime when it comes to trendy bracelets but I just love the bit of childish cheekiness they add to my otherwise serious jewelry collection. Thanks, Kate! You’ll need: assorted loom bands (also available here) plastic S clip (included in loom band orders)
Read more

DIY Pearl Choker & Rings

-
Image
By Erica Karl Lagerfeld turned up the ol’ pearl game about 100 notches with ginormous pearl necklaces, bracelets and rings for Chanel‘s spring collection. Costumey, over-the-top and DIYable . . . I was sold. Next came the painstakingly long search for the largest pearls I could find and in my hunt for pearls, came the inspiration to make rings inspired by Russian designer Maria Stern‘s super chic double pearl rings. It’s a pearl party and everyone is invited! You’ll need (for the pearl choker):     2 30mm pearl beads     12 gauge gold wire choker     2 ball end headpins     2 bead caps     E6000     a toothpick     heavy duty wire cutters You’ll need (for the pearl rings):     10mm & 12mm half drilled Swarovski pearls     8mm & 6mm half drilled Swarovski pearls     ultra thin gold rings     super glue     wire cutters
Read more